Solar Hard X-ray Albedo

From RHESSI Wiki

(Difference between revisions)
Jump to: navigation, search
Line 44: Line 44:
for three subcollimators with angular resolutions of 23, 69, and 217 arc seconds.  
for three subcollimators with angular resolutions of 23, 69, and 217 arc seconds.  
-
[[Image:SizeSensitivity.jpg|center|thumb|600px|Fig. 2: Modulation by 3 RHESSI subcollimators. Given a primary source size of 20 arcsec, as a function of subcollimator the amplitude of the modulation is less than <math>/sim</math> 7% for subcollimator 4 (and lower for the finer ones), but for the coarser subcollimators (6 and 8 in the above), the relative amplitude remains above 75%. This effect can be used to extract broad sources like albedo from small flare sources.
+
[[Image:SizeSensitivity.jpg|center|thumb|600px|Fig. 2: Modulation by 3 RHESSI subcollimators. Given a primary source size of 20 arcsec, as a function of subcollimator the amplitude of the modulation is less than &#126; 7% for subcollimator 4 (and lower for the finer ones), but for the coarser subcollimators (6 and 8 in the above), the relative amplitude remains above 75%. This effect can be used to extract broad sources like albedo from small flare sources.
]]
]]

Revision as of 00:22, 15 January 2010

Contents

Solar Hard X-ray Albedo

In the early days (1972) of solar hard X-ray flare observations, Fred Tomblin [1] published theoretical arguments that the hard X-ray spectrum of solar flares in the 5-40 keV range must have an albedo component due to Compton back-scattering in the photosphere of those primary bremsstrahlung photons that are emitted downward. In a more complete analysis, Taeil Bai & Reuven Ramaty [2] showed that this albedo component would be polarized and its size must depend on the height of the primary source.

The "reflected" photons form what is called an albedo patch. For sufficiently high primary source altitudes, the albedo would be much larger in extent than the primary source, with a size scale that increases with source height. (See Fig. 1 below.) Furthermore, the albedo source would be displaced toward disk center by a distance h sin θ, where θ is the heliocentric angle.


Why albedo has not been imaged before

A significant fraction (possibly as high as 40%) of the X-ray flux from solar flares comes from X-rays that propagate back to the solar surface from coronal sources and "reflect" off the photosphere. This component of flares is called the albedo, and it is remarkably difficult to observe because it is very diffuse with an intensity that is one or two orders of magnitude smaller than the primary flare sources themselves. Its importance for flare physics is that it both distorts the spectral interpretation of X-ray emission and offers a potentially powerful diagnostic of electrons accelerated in solar flares. Our study uses the unique capabilities of the Ramaty High Energy Spectroscopic Imager (RHESSI) to isolate this albedo component, determine its properties such as size, shape and centroid location as a function of energy. We have focused on single-component flares in the 12-30 keV range that appear within 45° of disk center. Using standard techniques, we have obtained the X-ray visibilities [3] (RHESSI Nugget # 39) of a number of such flares and applied Forward-Fitting methods to determine the parameters of the primary component (position, flux, and size) and the albedo-related parameters (primary source height and albedo flux).

Fig. 1. Model of a primary source (red) and its albedo patch (orange-yellow).

Fig. 1 shows how broad and relatively faint an albedo patch is compared to a compact primary source. The primary source (red disk) is taken to be a 2-D Gaussian, FWHM=5 arcsec, at a height of 18 Mm. The albedo patch is then computed under the assumption of isotropic scattering in the photosphere. Note that, while the peak brightness of the albedo patch is less than 1% of the primary source, too faint for direct imaging methods, most of the albedo flux would still be modulated by RHESSI's coarsest grids.

The primary source is taken to lie at 35° longitude and the resultant albedo patch is assumed to contain 40% of the total flux. The primary intensity is shown by solid contours (black) from 100% down to 1.5% of maximum. The albedo patch (yellow-orange) has intensities below 1% of the maximum. The green contours show the flux boundaries; the orange and red region together contain 80% of the total flux, and the yellow regions contain the remainder.


Sensitivity to source size

The modulation of RHESSI's count rates depends exquisitely on the grid pitch and the source size. This behavior is a fundamental property of Fourier imaging. For a given source size, the modulation amplitude increases as the subcollimator angular resolution broadens. This is illustrated below for three subcollimators with angular resolutions of 23, 69, and 217 arc seconds.

Fig. 2: Modulation by 3 RHESSI subcollimators. Given a primary source size of 20 arcsec, as a function of subcollimator the amplitude of the modulation is less than ~ 7% for subcollimator 4 (and lower for the finer ones), but for the coarser subcollimators (6 and 8 in the above), the relative amplitude remains above 75%. This effect can be used to extract broad sources like albedo from small flare sources.

Comparing this figure with Fig. 1, one sees that the 1% intensity contour (where albedo is the dominant contributor) is about 20 arcsec wide, so subcollimator 4 (and other finer ones) would show insignificant modulation, while the coarser subcollimators (6 and above) would show strong modulation.



Previous attempts to infer albedo properties

Full Exploitation of Fourier methods

We have found 9 flares with reliable enough amplitudes and phases to compare models of simple sources with albedo patches. The flares all lie within 45° of sun center, where albedo is expected to be strong. These flares form a small subset of RHESSI events for which MEM maps show only single, compact primary components in the range 12 to 30 keV.

Forward Fitting

Given the RHESSI amplitudes and phases for a flare, one may compare the observed values with those computed from a model. This process is called "Forward Fitting". At the present time, this method is reliable for computing albedo patch parameters only for single elliptical primary sources because the number of parameters (8 in this case) must be much smaller than the number of amplitudes. (For a discussion of Forward Fitting of amplitudes and phases, see RHESSI Nugget #35 [9] )

Amplitude model of a primary source both with and without albedo

Modeling the albedo patch in addition to the primary source makes it possible to infer the height of the primary source, and the fraction of the total flux emitted by the reflected photons. Here we show two examples of flares where the primary source amplitudes (blue crosses) are fit by a 6-parameter model (flux, position, ellipse FWHMs and orientation) with an albedo patch fit by 2 parameters (primary height and albedo fraction). In both cases, for comparison we show a fit made for a primary source without albedo.

Put fig 3 here.

Caption:

Comparison of observed and model amplitudes. Primary source amplitudes (blue crosses) are fit by a model of a non-back-scattered elliptical source (dashed red curve), and a model including both the primary and its associated albedo patch (solid red curve).
Each vertical colored band is for one of the subcollimators (SC) 3-9. Variations in the red curve at the top of each band are caused by rotation of the grids as the spacecraft spins.
The abscissa is a combination of subcollimator number (SC) and grid position angle (PA). The integer part of the x coordinate values is SC and the remainder is PA/180°. (Thus if x is, say, 3.4, SC=3 and PA = 0.4*180° = 72°.) The coarser subcollimators are to the right (SC=6-9), and these measure the flux coming from larger spatial scales.
The excess amplitudes of the solid red curve over the dashed red curve shown for subcollimators 6-9 represent the flux from the larger scales of the albedo patch. The black dashed curve shows the difference between the fitted amplitude profiles with and without albedo. Note how it drops into the noise for the finer grids 3 to 5.

Model Albedo Visibility Back-Projection

In those cases where the primary source and albedo patch are both well represented by a model, it is possible to display both sources using back projection. We have done this for a number of flares, with 2 example "bpmaps" here for the flares and bands of Fig. 3.

Put fig 4 here.

Caption:

The black contours show the primary source mapped from the model amplitudes and phases obtained by Forward Fitting, and the colors show a back-projection map made from the best-fit albedo model using completely sampled roll bins. The yellow arrow points from the primary to Sun center. The albedo patch centroid lies on this line because in three dimensions it lies vertically below the primary. In each case, the model albedo patch was back-projected from a Fourier plane with uniformly spaced roll bins.

Our Initial Conclusions

Using Fourier amplitudes and phases for nine simple (single primary, slowly varying) flares we have found evidence for X-rays back- scattered from the photosphere (the albedo patch). Note that these results are only for the so-called "thermal phase" when a single component dominates the emission.

We have visualized the albedo patch by back-projecting our Forward-Fit model of the best-fit albedo parameters. If the back-scattering process is isotropic (as we assume in the Forward-fit model), the albedo patch is displaced toward sun center from the projected location of the primary source, such that it is vertically below the primary source.

We make several inferences from our results for 9 flares:

Acknowledgements

The RHESSI software team has given invaluable help in making visibility software available to the community. Without their continued support, this research would have been impossible.

Biographical notes: Ed Schmahl is a retired University of Maryland and GSFC scientist, currently employed at NWRA/CoRA and Gordon Hurford is a senior RHESSI team member based at UC Berkeley.

Personal tools
Namespaces
Variants
Actions
Navigation
Toolbox